Hot Tubs Engineered for the World’s Harshest Climates

This is Christian Staples with Arctic Spas. And today, we’re going to go over how to hook up Ethernet over power. So this is a way of hooking your Arctic Spa up to the Internet without using WiFi.

So one of the problems that we ran into with WiFi sometimes is that you run into an issue of interference because the WiFi’s on the outside of the house, or sometimes it’s a low-signal strength. So what this does is it removes those variables from it, and we run the Internet essentially over your power line that feeds the hot tub.

So to do this, we’re going to open up the box here. The first thing that you want to do is shut the power off. And then we’ll just simply remove the screws. I’ve removed all the rest of them just to make it faster.

And then we have our Ethernet over power module here. So this comes in two pieces. This one here that we’ve attached the wires to is going to go inside the pack. So what you want to do is you want to find this plug right here called J21. So it’s right there. And you’re going to take one of the leads and hook it up to the J21. You just slide that right over.

And then the other one is the neutral. So you want to put it right on to the neutral bar. Any of the neutrals will work. But you just slide it right on to there. Make sure it’s on nice and snug.

And then you’re going to take the Ethernet cord. You’re going to plug it into the bottom of the module and then also into the motherboard over on this side here.

And then all of this will have to fit in here, so we’ll just have to find a place for it to fit. And then we got to go hook up the other side at the wireless router.

So what we’re going to do is we’re going to take and we’re going to plug in the module into the wall here. And then plug your Ethernet cable into the bottom.

So then what you want to do is you want to plug in the Ethernet cable into your wireless router or your modem, whatever you use for your wireless. So what we want to do now is make sure on both modules that all the lights are on, and this would determine that both modules are connected and talking to each other. So you can see by the lights there they’re all on solid.

So when it’s paired, you should see this light light up, and it will tell you that it’s communicating with the other module. If you don’t, we’re on the wrong power line. So because the spa works off of both power lines, and a 110 volt system just works off of 1, we need to make sure that we’re on the right power line. So what you want to do is you want to remove this J21 plug and plug it in here to the line 2 terminal bar. Just any one of those will work. So there you go, just hook it right up to the line 2 side. And then it should pair with the other module.

Okay, so now what we need to do is we need to go in and tell the hot tub that we need to have a dynamic IP address instead of a static IP address. So we do that in the settings button. On an Epic series with five pumps, it’s going to be pump number 5. Or it will be in the same position on any of the other tubs just for the settings button. But we hold down this button for about 20 seconds until on the screen it says LLP.

Okay, so now don’t adjust anything else. Otherwise, you’re probably going to be giving us a call. And just go down until you see IP. So right now, it’s set to ST, which is static. We’re going to change it to DY, which is dynamic. And then we’re going to scroll down through the rest of the options.

We’ll let the spa reboot. Once it has rebooted and you have your current temperature here, we’re going to take and turn the power off at the breaker and then turn it back on. So I’m going to go do that now.

It’ll take just a second for it to reboot up now. And then we should be good to go.

And once you have the current temperature now, you’re back to normal. Now, what we need to do is go on to our computer and connect up to the spa.

So right now, we’re going to talk about how to register your spa on myarcticspa.com. This will give you the access over the Internet to control your hot tub.

Okay, so now, we want to go to our computer. Make sure that you’re connected to the same network as that wireless router. And if you’re as cool as us, you name it Arctic. And we want to go to myarcticspa.com.

So now, once you pull it up, we want to create a user name and password and register the spa. So we’re going to do a new registration. So this one we’re going to name Arctic Spas Utah. And we’re going to use my email address. And then you’ll create a password. And then we click here to register. So now, it says choose a password, so we got to enter our password in. Confirm your password and confirm your email address. And then we have some security questions. So we’ll go through them. I have no idea what the first movie I saw, but I do know the middle name of my oldest child. And then you enter your first name and last name and a phone number, address. You select your country.

So now this point, it’s going to search for the spa. And it’s going to come up with a code on the hot tub itself. So we’re going to press Search.

Okay, so now, this is the code that comes up here. And all we have to do is just push a button, and it will configure it.

So now, we can actually see the spa here. So we’re going to click on Register. So now, it’s going to ask you for a nickname. You can come up with any name that you want. And then it’s asking you for the spa number. So this is going to be your serial number but just the number part of the digits.

So in order to find the serial number, it’s right on this plate here if you don’t have it any other way. And the serial number’s just located right there.

So our serial number is 157308. And then we just press enter.

Now, it says that it’s been successfully registered, and we can control My Arctic Spa now. So now, it says our current temperature is 101. We can turn on the pumps just by pressing these buttons here. We can turn on the light. All of your settings are right here. And then a really neat feature is this Power Consumption that’s under Diagnostics. And we can actually look and see how much our spa is actually costing us to run.

So that’s how you register your spa and access your spa on myarcticspa.com and hook it up to the Ethernet over power.

More hot tub repair tutorials and videos are here.